專用中央供料系統風機故障排除方法

專用中央供料系統風機故障排除方法：
專用中央供料系統風機故障排除方法如發現溫度升高，它的原因有如下幾點：
1、環境溫度增高——增加環境通風散熱。
2、工作狀態改變——調整工作狀態；
3、軸承干潤滑——加軸承油脂；
4、風機效率降低——**葉道塵?；蚋鼡Q泵頭；
5、進氣口溫度過高——降低進氣口溫度；
專用中央供料系統風機故障排除方法如出現震動增大，它的原因有如下幾點：
1、工作狀態進入湍震區——調整工作狀態，避開湍震區；
2、主軸變形——更換主軸或泵頭；
3、葉輪不平衡——**葉輪中異物或校動靜平衡；
4、軸承損壞——更換軸承；
專用中央供料系統風機故障排除方法如出現噪音增大，它的原因有如下幾點：
1、軸承干潤滑——加軸承油脂；
2、軸承損壞——更換軸承；
3、葉輪磨損——更換葉輪或泵頭；
4、堅固件松動或脫落——擰緊緊固件；
5、風機內有異物——**異物或更換泵頭。
5、進出氣口進濾網堵塞——清洗過濾網。
專用中央供料系統風機故障排除方法如發現風機不轉動，它的原因有如下幾點：
1、未接通電源——接通電源；
2、電機不工作——檢查電機接線或更換電機；
3、風機頭損壞——修復風機或更換；
4、風機中有異物卡死——**異物Dedicated central feeding system fan troubleshooting method:
one,. If the temperature is found, it has the following reasons:
1, the ambient temperature increases - increase the environment ventilation cooling.
2, working state change - adjust the working state;
3, bearing dry lubrication - plus bearing grease;
4, reduce the efficiency of the fan - remove the leaf dust or replace the pump head;
5, the inlet temperature is too high - to reduce the inlet temperature;
Second, if there is increased vibration, it has the following reasons:
1, the working state into the turbulent area - to adjust the working state, to avoid the turbulent area;
2, spindle deformation - replace the spindle or pump head;
3, the impeller imbalance - remove the impeller in the foreign body or school static balance;
4, bearing damage - to replace the bearing;
Third, if the noise increases, it has the following reasons:
1, bearing dry lubrication - plus bearing grease;
2, bearing damage - replacement of bearings;
3, impeller wear - replace the impeller or pump head;
4, the firmware loose or off - tighten the fasteners;
5, foreign body in the fan - to clear the foreign body or replace the pump head.
5, into the air inlet into the filter plug - cleaning filter.
Four, if the fan does not turn, it is the following reasons:
1, not connected to power - connected to power;
2, the motor does not work - check the motor wiring or replace the motor;
3, the fan head damage - repair fan or replacement;
4, the fan has a foreign body stuck - remove foreign body